[KARAOKE] [DJ GEAR] [GUITARS] [LIGHTING] [LIGHT BULBS] [NEW GEAR] [USED GEAR] [RENTALS] [BLOWOUTS!]
Crate VFX5212 Amplifier
Crate VFX5212 Amplifier at the lowest prices! Power Alley is an authorized dealer for Crate VFX5212 Amplifier! Free shipping on Crate VFX5212 Amplifier. Call 800-788-9552 for the best deal on Crate VFX5212 Amplifier!
5 YEAR Transferable warranty!
The VFX5212 is a dual channel Class A/B amp that delivers 50 watts RMS from a pair of EL34 tubes, to power two internal 12" Celestion speakers. It feature 15 digital effects designed to replicate the best reverbs, delays, and vibrato effects available from any manufacturer from any era. They're individually assignable to each channel so when you switch channels, you instantaneously switch up to four effects (two per channel) with the included two button footswitch.
| 1. Input:
Connect your instrument here by means of a shielded signal cable. 2. Volume: Use this control to adjust the output level of Channel A. 3. Treble: Use this control to adjust the output level of the high frequencies for Channel A. This control provides an adjustment range of 30dB at 10kHz. 4. Mid: Use this control to adjust the output level of the middle frequencies for Channel A. This control provides an adjustment range of 6dB at 600Hz. 5. Bass: Use this control to adjust the output level of the low frequencies for Channel A. This control provides an adjustment range of 30dB at 80Hz. 6. Channel Select: This switch, when depressed, activates Channel B. Channel A is active when the switch is in the out position. 7. Gain: Use this control to adjust the gain for Channel B. With the control towards the counter clockwise position, the gain is low and very little distortion is present. As you rotate the control clockwise the gain increases, producing more overdrive distortion and a higher output volume level. 8. Treble: Use this control to adjust the output level of the high frequencies for Channel B. This control provides an adjustment range of 10dB at 4kHz. 9. Mid: Use this control to adjust the output level of the middle frequencies for Channel B. This control provides an adjustment range of 10dB at 1kHz. 10. Bass: Use this control to adjust the output level of the low frequencies for Channel B. This control provides an adjustment range of 12dB at 100Hz. 11. Level: Use this control to adjust the output level of Channel B. 12. DSP Mode: Use this control to select which of the following digital effects to apply to the signal. BYPASS no effect SMALL REV small room reverb MED REV medium room reverb LARGE REV large hall reverb SLAPBACK short slapback echo DELAY 1 short delay w/regen DELAY/REV 1 short delay w/reverb DELAY 2 long delay w/regen DELAY/REV 2 long delay w/reverb VIBRATO SLOW slow smooth vibrato VIBRATO FAST fast vibrato/tremolo CHORUS medium chorus CHO/REV medium chorus w/reverb CHO/REV/DELAY med cho w/reverb/delay SLAP CHORUS slapback echo w/chorus T-WAH touch-sensitive wah-wah 13. DSP Level: Use this control to adjust the level of the DSP effect. With the control rotated fully counter clockwise, no effect will be audible. As the control is rotated clockwise the amount of the effect is increased. 14. Presence: Use this control to adjust the overall brightness and punch of the output signal. 15. Lamp: This lamp illuminates when the amplifier is turned on. 16. On/Standby Switch: Use this switch to activate the amplifier after the On/Off Switch (#17) is turned on. Always turn this switch OFF first and ON last! Turn the On/Off Switch (#17) on at least 30 seconds before turning on the Standby switch. During short breaks you should turn this switch off and leave the On/Off Switch on. This will help prolong the life of the amplifier’s tubes. 17. On/Off Switch: Use this switch to turn the amplifier on and off. Always turn this switch ON first and OFF last! Turn the Standby switch (#16) on at least 30 seconds after turning on the On/Off Switch. |